BOUNTY HUNTER - 2005 32' FARALLON BOATS Explorer 3200
Alameda California $149,000 USD
Yacht for sale is a 2005 FARALLON BOATS 32' "BOUNTY HUNTER" Explorer 3200 Sport Fisherman in Alameda, California, United States. One owner boat! Bought 11/2012 from Farallon, Farallon demo boat from ’07 to ‘12. Well equipped and well maintained. Rated one of the West Coast's best fishing boats. Farallons are used commercially as well as privately, that's how good they are!
LENGTH 32' (9.75m)
BUILDER FARALLON BOATS
ASKING PRICE $149,000 USD
BUILT (REFIT) 2005
BEAM 9' 6" (2.90m)
MX SPEED N/A
CRUISING SPEED N/A
GROSS TONNAGE 0.00
LOCATION Alameda California United States
Power Train - Cummins Diesel QSB5.9-330HD
(Engine number 46411854), 26.3 KTS @ 2800 RPM
(Upgraded by Cummins to 370 HP@3000RPM, (900 Hours)
Serviced by Hai Nguyen, Performance Diesel, Moss Landing
ZF 85 IV Transmission with Trolling Valve -
ZF Cruise Command 785CE Control
Centerline 31'3" Overall Length 32'2"
Beam 9'8" Freeboard Fwd/Aft 45"/36"
Draft w/IB or IO 3'10"
Deadrise (Constant) 18°
Aft Work Deck (Sq . Ft.) 178.5
Crown On Aft Work Deck 1 3/4"
Fall To Aft On Work Deck 5"
Construction / Materials
Battery Box(s)----------Fiberglass bonded bases
Deck Hardware--------Stainless steel bolted
Engine Mounting------1/2" (min.) marine grade aluminum angle foundation. Horizontally bolted through 2.5" stringers.
Fuel Lines---------------USCG Type A1
Fuel Tanks--------------Marine grade aluminum (baffled)
Handrails----------------Welded stainless steel
Rubrails------------------2" vinyl extrusion (S/S fastened)
Construction: Hull: (Hand Laid)
1.25 oz mat, 24 oz woven roving, 3/4" thick at keel, 5/8" thick at chine, 3/8" thick at freeboard
2.5" fiberglass encapsulated marine plywood. Limber holes for drainage.
3/4" fiberglass encapsulated marine plywood
3/8" fiberglass encapsulated with high density foam core.
Molded fiberglass stiffened with fiberglass encapsulated 3/4" Balsa core. Fiberglass bonded to hull with mat and roving.
Molded fiberglass stiffened with 3/8" end cut - balsa core.
Electronics / Electrical
Furuno TZ Touch 14” Network Display (new 7/2013)
Furuno TZ Touch 9” Network Display (new 7/2013)]
Furuno DFF1-UHD Chirp Sonar and Transducer (new 7/2013)
Furuno DFF-3D Multi-Beam Sonar and Transducer (new 1/2018)
Furuno CH/270 Color Searchlight Sonar
Furuno DRS4A 4KW 48NM 3.5FT Open Array Radar (new 7/2013)
ICOM IC-M602 Radio
Installed and Serviced by Terry Boland, Maritime Electronics, Santa Cruz, CA
Batteries - Engine Battery 194 AH Interstate ACV 4A8D (new 2013)
Inverter Battery 280 AH Interstate ACV 8A8D (new 2013)
House Battery 280AH Interstate ACV 8A8D (new 2013)
Xantrex Freedom SW 3012 3.0 kW Inverter/Charger (new 1/2016)
19si 12v 160amp Alternator (new 1/2016)
Combiners / Relays - Dual BlueSea 500 Amp ML-ACRs (new 1/2016)
BlueSea Engine Battery Disconnect Remote Relay
BlueSea Systems M2 State-of-Charge 3 battery monitor (new 2018)
Boat Re-wired by Larry Scroggins, Scroggins Electric, Santa Cruz, CA and Terry Boland Maritime Electronics 1/2016
Fuel System -
Dual 100 Gallon Aluminum tanks - Seaboard Marine Quantum Double Filter System with Squeeze Bulb, Groco valves and Parker brass fitting
Simrad AP25 Autopilot
Linear Devices Lectrotab Electromechanical Trim Tab System
Vetus BOW2512E Bow Thruster (new 2//2019)
Bow Thruster Shutoff switch installed 2/2019
Water / Plumbing / Refrigerator / Microwave
Toilet, Holding Tank
Force10 Electric Water Heater
Norcold NR751 AC/ DC Refrigerator (new 8/2017)
Revere Offshore Extreme Life Raft (new 7/2013)
EPIRB ACR Model RLB-41 with 10 year battery (new March 2018)
SPURS line and net shaft cutters
Anchor with 150 foot rode
Wipers (new 1/2016) Need an adjustment
3 Bilge Pumps @ 1000GPM
Fishing equipment (included)
2 19 foot Outriggers
3 Cannon Magnum 10 STX Stainless Steel Tournament Electric Downriggers 2 installed, one spare (new 2013)
EZ-Pull Electric Crab Puller (new 2013)
Bait Tank - Magma Fish / Bait table
Large Flush-Deck Fish Box with Macerator
(Recent) Maintenance Logs...
2-week Haulout at Santa Cruz Boatyard (Replaced Bow Thruster with complete new Vetus unit)
Replaced all Zinc Anodes prop shaft plate trim tabs rudder Replaced all bonding wiring throughout boat
Replaced thru hull bonding fittings as needed
Sanded, Prepped, Epoxied and Painted bottom
Sanded / Removed old paint
Repaired all bottom issues including blisters
Applied Epoxy Barrier Coat
Applied new bottom paint
Engine Service (Kevin) Changed fuel filters, Changed oil filter, Changed engine oil, Changed transmission oil filter, Changed transmission oil, Changed Impeller, Changed after cooler gasket,
Replaced all engine anodes August 2019
January 2020 Haulout and replace all Zincs
Power Wash bottom Semi-Monthly
Diver maintenance on bottom
Topside clean and scrub